you're reading...
Uncategorized

New FAA Guidance on Propeller PMA Parts – Open for Comment

The FAA has published a draft policy statement on PMAs for critical propeller parts.  The draft policy statement is entitled “Parts Manufacturer Approval (PMA) for Propeller Critical Parts and Category 1 Propeller Parts.”  If this policy effects you, then we need to know your opinion before we file the MARPA comments on this draft policy!

The essence of the proposed policy appears to be:

  • Defines a set of parts subject to enhanced oversight that includes:
    1. Critical propeller parts identified by § 35.15 Safety analysis
    2. Parts identified as critical in FAA Order 8110.42D
    3. Category 1 parts defined in FAA Order 8120.23A [this could have the effect of applying critical parts requirements to parts that are not critical under the FAA regulations]
    4. Parts with airworthiness limitations
  • Defines certain parts as presumptively critical:
    • Certain blades, hubs, and counterweights
    • Certain primary load path blade retention parts, such as ferrules and blade clamps
    • Certain metallic blade erosion shields
    • Certain blades and counterweights
    • Certain blade pitch change pins
    • Certain pitch change links, yokes, and forks
    • Pitch change system parts:
      • Pressure cylinder, piston, actuator, seals, and springs
      • Beta feedback rods
      • Low and high pitch stops
      • Oil transfer tubes
    • All parts of the propeller control system:
      • Governors
      • Propeller control units
      • Propeller electronic controls
      • Propeller servo valves
  • Requires that an applicant seeking to PMA parts subject to enhanced oversight must coordinate the application with the certificate management ACO (for the type certificate) and the Engine and Propeller Directorate
  • Imposes on the PMA applicant a series of life management obligations for parts subject to the policy:
    1. The PMA applicant is responsible for determining if the part has been life assessed;
    2. A part specific certification plan is required for life assessed critical PMA propeller part(s);
    3. The part specific certification plan must include a fatigue life methodology that supports a continued airworthiness life management program (this appears to be something potentially more than the service management process required by the regulations).
    4. When managing propeller critical parts and category 1 propeller parts, the applicant must provide a program to monitor those parts and establish a life management program.

One concern is that a major propeller effect (as defined in 14 C.F.R. 35.15(g)(2)) is different from a hazardous propeller effect (as defined in 14 C.F.R. 35.15(g)(1)).  Only parts whose failures result in hazardous propeller effects are propeller critical parts under 14 C.F.R. 35.15(c).  And only propeller critical parts are required to meet the integrity establishment requirements of 14 C.F.R. 35.16.  But the policy document establishes additional classes of parts that will be subject to section 35.16.  Some parts with major propeller effects (as defined in 14 C.F.R. 35.15(g)(2)) could also be characterized as category 1 parts under FAA Order 8120.23A.  This policy memo appears to subject those parts to an inappropriate requirement by conflating them with propeller critical parts and requiring that they comply with the integrity establishment requirements of 14 C.F.R. 35.16.  This appears to be a potential de facto change to the regulations.

What do you think?  Do you have category one parts whose failure only reflects a major propeller effect and not a hazardous propeller effect?

Do you see any different impact?  Anything we’ve missed?  How does this affect your business?  Let us know so that MARPA’s comments on this policy can reflect your interests.

Comments on this draft are due to the FAA by August 31, 2017.  We would appreciate your comments to MARPA by August 24.

Advertisements

About Jason Dickstein

Mr. Dickstein is the President of the Washington Aviation Group, a Washington, DC-based aviation law firm. He represents several aviation trade associations, including the Aviation Suppliers Association, the Aircraft Electronics Association, the Aircraft Fleet Recycling Association and the Modification and Replacement Parts Association.

Discussion

Trackbacks/Pingbacks

  1. Pingback: MARPA Files Comments on Propeller PMA Policy | MARPA - September 11, 2017

Leave a Reply

Please log in using one of these methods to post your comment:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: